Raised-panel steel
Modern flush
LiftMaster openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Get your free estimateTrusted Garage Door Spring Repair for Houston Homeowners
When a garage door spring snaps in Houston, the door becomes dead weight as fast as the humidity settles in. Most torsion springs are rated for roughly 10,000 cycles, which in a busy Houston household means about 7 to 10 years of daily use before failure. When they break, it often sounds like a gunshot from the driveway, and the door will not lift, no matter how hard the opener strains. Our technicians at Bramwell Garage Doors Houston provide our Garage Door Spring Repair in Houston across the city every day, usually the same day you call. Call (903) 989-4180 and a live person picks up, 24/7, not a voicemail tree. Marcus Ellery and the team have worked under the Kingswell standard since 2001, which means a written price before any work starts, a real arrival window, a clean job site, and the 365-Day Done Right Promise in writing on every single repair.
Garage Door Spring Replacement
Garage Door Spring Replacement is the service you need when the coils that counterbalance your door have reached the end of their cycle life, lost tension, or snapped outright. In Houston, the heat and humidity do not dramatically shorten spring life, but daily use does: two car doors cycling four times a day will wear a spring out in about seven years. Bramwell Garage Doors Houston replaces springs for all major brands, including Genie and Clopay models, and the job typically runs $180 to $340, parts and labor included. We carry the common spring sizes on the truck, which means most replacements happen in a single visit.
When Replacement Beats Repair
A stretched spring can sometimes be retensioned, but once torsion springs show visible gaps in the coil, replacement is the honest recommendation. Repairing a fatigued spring is a short-term patch that fails again, often within months. The 365-Day Done Right Promise means if our replacement fails within a year, we come back and fix it at no charge, in writing.
Paired Spring Replacement
Both springs on a two-spring door wear at about the same rate, even if only one breaks. We recommend replacing both at once to keep the door balanced, which protects the opener motor and rollers. The written quote you get before any work starts will show both prices clearly, with no surprises on the invoice.
Styles & brands we work with
Garage Door Torsion Spring Replacement
Garage Door Torsion Spring Replacement addresses the heavy steel coil mounted on a shaft directly above the door opening, the component that handles most of the lifting weight. Torsion springs are under extreme tension, sometimes holding 200 pounds or more each, and Houston homes with standard 7-foot doors almost always use one or two of them. Replacement by Bramwell Garage Doors Houston costs $180 to $340, which includes the spring, labor, winding, and balancing of the door. This is not a do-it-yourself job under any circumstances; the winding bars alone store enough energy to cause severe injury if mishandled.
How a Torsion Spring Fails
Torsion springs fail from metal fatigue, not abuse. Every open and close cycle flexes the wire, and eventually a micro-crack grows until the spring snaps. Homeowners in Bellaire often describe the break as a loud bang from the garage, followed by the door refusing to move, and we offer our Garage Door Spring Repair in Bellaire for exactly this situation.
Calibrating to the Door’s Weight
The replacement spring must match the weight and height of the specific door, not just the old spring’s dimensions. Our technicians weigh the door and verify wire size and spring length before installing anything. A mismatched spring undershoots or overshoots the balance, and the opener burns out early, which costs more than the spring ever would.
Broken Garage Door Spring
A Broken Garage Door Spring is an urgent problem because the door is either stuck closed or can be yanked open manually by someone with enough force, a security concern for any Houston homeowner. The spring is the only thing making a 150 to 200 pound door feel light. Without it, the opener cannot lift the door, and trying to force it up with the opener engaged can strip the gears inside the motor. Bramwell Garage Doors Houston fixes broken springs the same day in most cases, with prices in the $180 to $340 range. When you call (903) 989-4180, a person answers and schedules a real arrival window, not a four-hour gap.
Why You Should Not Use the Opener
When a spring breaks, press the wall button or remote only once to confirm the failure, then leave the opener alone. Continuing to run the opener strains the gear train inside the unit, which can push a simple spring repair into a $120 to $320 opener repair. The safe move is to leave the door closed and call us.
Balancing After the Break
A broken spring rarely fails alone in a two-spring system. The surviving spring has the same number of cycles on it and is likely close behind. We replace both springs when we find a broken one, so the door lifts evenly and the new spring is not doing double duty from day one.
Garage Door Extension Spring
A Garage Door Extension Spring runs along the horizontal track on each side of the door and stretches to provide lift, unlike the torsion design that sits above the door. Older Houston homes, especially in established neighborhoods like Deer Park and Pasadena, often have extension spring systems on lighter single-car doors, and we provide Garage Door Spring Repair - Pasadena for these systems. These springs cost less to replace, but when an extension spring fails, it can send a heavy steel hook flying across the garage, which is why modern code requires a safety cable inside every extension spring. Bramwell Garage Doors Houston replaces and safety-cables extension springs for $180 to $340, and we inspect the pulleys and brackets at the same time.
Why Safety Cables Matter
Houston building code has required containment cables inside extension springs for decades, but we still find doors without them, usually after a handyman replacement. A snapped extension spring without a cable becomes a projectile. We install the safety cable as part of every extension spring repair, no separate trip charge.
Converting to Torsion
Some homeowners with extension springs ask about converting to a torsion system, which balances the door more smoothly and lasts longer. The conversion requires new bearing plates, a shaft, and a torsion spring sized to the door, and we will quote the exact cost before any work begins. Many homes in Jersey Village and Stafford have made the switch, and the written price you approve is the price you pay.
Garage Door Spring Installation
Garage Door Spring Installation covers both brand-new doors that need springs matched to their weight and older doors that need fresh springs after a conversion or door replacement. The cost for installation only, without any door work, runs $180 to $340 in Houston, and Bramwell Garage Doors Houston stocks springs for Amarr and Wayne Dalton doors as well as all the other common residential brands. On a new door install, the springs are part of the package, but when we are replacing just the springs, the quote you approve before work starts includes everything: spring, winding, lubrication, and balance testing.
Cycle-Rated Springs
We install springs rated in cycles, not years, because cycles measure how many times the door goes up and down. A 10,000-cycle spring lasts about seven years of normal use; a 20,000-cycle spring lasts roughly double that. If you plan to stay in the house, the higher cycle rating costs a little more up front and pays off in years of reliable service.
Lubrication and Balance Check
After installing any new spring, our technicians lubricate the spring, hinges, and rollers with a garage-door-specific lubricant, then cycle the door several times to confirm balance. A properly balanced door stays put when opened halfway by hand. That is the standard every Bramwell technician works to, on every job, in every Houston neighborhood from Cinco Ranch to Channelview, where we also offer our Garage Door Spring Repair in Channelview.
Garage Door Spring Adjustment
Garage Door Spring Adjustment is the process of adding or releasing tension on a spring so the door balances correctly. Over time, springs settle, doors shift, and homeowners notice the door drifting up when it should stay down or sagging when it should hold position. Bramwell Garage Doors Houston handles adjustments as part of a service call, and in many cases the adjustment is covered if we installed the spring under the 365-Day Done Right Promise. A standalone adjustment call runs $120 to $240, depending on travel and what we find on the door.
Torsion Spring Tensioning
Adjusting a torsion spring means adding quarter-turns to the winding cone with steel winding bars. This is dangerous work; a winding bar that slips can shatter a wrist or worse. Our technicians do this every week and carry the correct diameter bars for the springs on your door.
When Adjustment Is Not Enough
If a spring has visible gaps, rust, or stretched coils, tightening it further shortens its remaining life and increases the risk of a snap. In that case we will show you the spring and give you a written quote for replacement. We do not charge you for an adjustment that does not fix the problem if you approve the replacement right then.
Brands We Service
Bramwell Garage Doors Houston works on residential doors from all the major manufacturers, and our technicians are trained to service Genie, Clopay, Amarr, Wayne Dalton, LiftMaster, Chamberlain, Craftsman, and Raynor systems. We stock common torsion and extension spring sizes for the brands most common in Houston’s housing stock, and the trucks carry OEM or spec-equivalent parts, not generic knockoffs. If you have a Clopay door in Cinco Ranch or a Wayne Dalton in Pearland, the technician who arrives at your door knows the specific spring and bracket layout that door uses.
An Amarr door uses a different spring winding method than older Wayne Dalton models, and Genie openers pair with specific spring balance profiles. Whether you have a Genie, Clopay, Amarr, Wayne Dalton, or any other make, we can replace the spring, balance the door, and get it running quietly again.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- The door will not open, and you heard a loud bang from the garage. That bang is the sound of a torsion spring breaking under tension. Continuing to press the opener strains the motor gears and can double your repair bill.
- The door opens a few inches, then stops. A fatigued spring cannot provide the lift the opener expects, and the safety system on the opener often reverses the door. The spring is failing, not the opener.
- The door feels heavy when you pull the manual release cord. A properly balanced door should feel manageable to lift by hand, roughly 8 to 10 pounds of effort. If it feels like dead weight, the spring has lost tension.
- You can see a gap in the spring coil above the door. Torsion springs should be one continuous coil. A visible separation means the spring is broken or close to it and needs replacement.
- The door slams shut or jerks while opening. When spring tension is uneven, the opener pulls harder on one side than the other. That uneven load wears rollers, bends tracks, and shortens the opener’s life.
Our Process, Step by Step
- 1
You call, a live person answers. Every call to (903) 989-4180 is answered by a real person, 24/7, including nights, weekends, and holidays. We ask about your door: brand, number of springs, and what happened when it failed, then give you a real arrival window.
- 2
We arrive in uniform and inspect the door. The background-checked technician checks the spring, cables, pulleys, rollers, track, and opener. We measure the door weight and spring wire size before recommending anything, so the repair matches the actual door, not a guess.
- 3
You approve a written price. Before any work starts, you get a written quote showing parts and labor. The number on the invoice matches the number on the quote, no door-step price changes, no hidden service fees.
- 4
We complete the repair and balance the door. The technician installs the spring, winds it to the door’s weight, lubricates moving parts, and cycles the door several times. We test the balance by hand and adjust until the door holds position at half-open.
- 5
We leave the garage clean and hand you the written guarantee. Every repair includes the 365-Day Done Right Promise in writing. If a covered repair fails within a year, we come back and fix it at no charge. The Kingswell Guarantee covers the work, and we leave the job site cleaner than we found it.
How Much Does Garage Door Spring Repair Cost in Houston?
A typical garage door spring repair in Houston runs $180 to $340, and that includes the spring, labor, and balance testing. A single torsion spring replacement tends toward the lower end of that range, while a double-spring replacement on a heavier two-car door lands at the upper end. Cable repair, often needed when a spring snaps, adds $130 to $250, and roller replacement, which we recommend when the old rollers have worn flat spots, adds $110 to $220.
What affects the price most is the spring’s cycle rating and the door’s weight. A high-cycle spring rated for 20,000 cycles costs more than a standard 10,000-cycle spring but lasts roughly twice as long. Houston’s humidity does not damage springs directly, but it accelerates rust on older springs, and a rusted spring has a shorter remaining life, so we may recommend replacement over adjustment. The best way to avoid overpaying is to get a written quote before any work starts, which is exactly how Bramwell operates. The free estimate includes a full inspection of the springs, cables, and balance, and you approve the price before we touch a wrench.
Our Service Area Near Houston
Bramwell Garage Doors Houston covers the whole metro from Garage Door Spring Repair in Houston out to the surrounding communities. Most calls inside the Loop get same-day service, and we routinely run to Pearland, Pasadena, Cinco Ranch, Jersey Village, Stafford, Deer Park, Bellaire, West University Place, and Channelview. For homeowners north of the city, we also cover Garage Door Spring Repair in Spring and Garage Door Spring Repair in Humble. If you need opener work or a full door replacement, see our related services for home garage door solutions.
Serving Houston, TX - Our Local Coverage Area
We’re based in the Houston area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Garage Door Spring Repair in Houston
Garage door spring repair is the process of replacing or re-tensioning the steel coils that counterbalance your garage door. Most Houston homes use torsion springs mounted above the door, and when those springs wear out or break, the door will not open safely. Call (903) 989-4180 for an exact quote, and we will inspect the spring before recommending any work.
A typical torsion spring replacement takes about 45 to 90 minutes once the technician begins work. If the door needs additional adjustments, such as cable replacement or track realignment, the visit may run closer to two hours. Most repairs in Houston are finished the same day we arrive.
Garage door spring repair in Houston costs $180 to $340, parts and labor included. The final price depends on the door’s weight, the spring’s cycle rating, and whether both springs need replacement. You will get a written price before we start, so the invoice never surprises you.
Yes, we service Genie and Clopay doors as well as Amarr, Wayne Dalton, LiftMaster, Chamberlain, Craftsman, and Raynor. Our trucks carry common spring sizes for the brands most often found in Houston neighborhoods. Bring us any residential door and we will match the correct spring to its weight and size.
In most cases, yes. We keep spring sizes on the truck for the most common Houston door configurations, so a broken spring can usually be replaced the same day you call. Call (903) 989-4180 and we will give you a real arrival window, not a four-hour gap.
The 365-Day Done Right Promise covers the repair we perform for a full year. If a covered spring or repair fails inside that year, we come back and fix it at no charge. The promise is in writing on every job, not just spoken at the door.
Clear enough space in the garage for our technician to work comfortably around the door, and move any vehicles outside if possible. If your door is stuck closed and you need the car out, our technician can often release the door manually when the spring has broken, as the spring is no longer under load. Have the door’s brand and model year handy if you know them.
Schedule Your Garage Door Spring Repair Service in Houston Today
A broken spring only gets worse with every attempt to open the door. Call (903) 989-4180 now and a real person answers, day or night. We’ll give you a written price before any work starts and stand behind the repair with the 365-Day Done Right Promise.
Written by Marcus Ellery, Owner at Bramwell Garage Doors Houston, serving Houston since 2001.